Optimization of Drilling Process Parameters For Aluminum ALLOY AA8011
DOI:
https://doi.org/10.30732/CSVTURJ.20211002006Keywords:
Drilling, , Aliminium alloy, , Optimization, , Process parametersAbstract
In the industry, the drilling process is the most interesting among all the other machining process which has to maintain quality of holes required for producing riveted and bolted joints in the many more operation of workpiece. The major tasks which arise from the drilling on any materials are characterized by the poor hole quality which might initiate cracks within its frame structure and reduces their reliability. Predicting the optimal parameter has become increasingly important given the rise in expenses involved in drilling a well. Several models and methods have been published for predicting, and therefore potentially optimizing. However, these models and methods have limitations, too many variables are included, their input parameters are often not readily available, and their relationships are complex and not easily modeled. Therefore, the optimization technique of grey relation analysis is suggested in this work. Another methodology has been developed to predict the parameter of responses by ANOVA method. The system uses a knowledge base of various drilling parameters, to produce a “correlation” description of the responses. These responses are predicted by ANOVA method.
References
Aamir, M., Tu, S., Tolouei-Rad, M., Giasin, K., Vafadar, A. (2020), Optimization and Modeling of Process Parameters in Multi-Hole Simultaneous Drilling Using Taguchi Method and Fuzzy Logic Approach, MDPI Materials, 13(680), doi:10.3390/ma13030680.
Abhishek K, Sonkar V, Datta S, Mahapatra SS (2014) Optimization in drilling of MMC composites. J Basic ApplEng Res 1(2), Pp.79–83, https://doi.org/10.1088/1757-899x/149/1/012103.
Amrana, M. A., Salmah, S., Hussein, N.I.S., Izamshah, R., Hadzley, Sivaraos, M., Kasim, M.S., Sulaiman, M.A. (2013), “Effects of machine parameters on surface roughness using response surface method in drilling process”, The Malaysian International Tribology Conference 2013, MITC2013, Procedia Engineering, 68 (2013), Pp. 24–29.
Bharti, A., Moulick, S K. (2013) “Parametric optimization of multi response factors in micro drilling operation”, International Journal of Scientific & Engineering Research, 4(7), Pp. 1157-1163.
Cheng, C. P., Wu, K. L., Mai, C. C., Yang, C. K., Hsu,Y. S. (2010) “Study of gas film quality in electrochemical discharge machining”, International Journal of Machine Tools And Manufacture, 50, 2010, 689-697.
Davim, P. J. (2003) “Study of metal-matrix composites based on the Taguchi techniques”, Journal of material processing technology, 132(1), Pp. 250- 254
Demir Z. An experimental investigation of the effects of point angle on the high-speed steel drills performance in drilling. Meas Control 2018; 51(9–10):417–30.
Garg S. (2015) “Effect of Material Removal Rate (MRR) on AISI H11 Die Steel in Drilling using Face Centered Design”, IJSTE - International Journal of Science Technology & Engineering, 1(11), Pp.400-41, ISSN (online): 2349-784X.
Goyal, K. K., Jain, V., Kumari, S. (2014) “Prediction of Optimal Process Parameters for Abrasive Assisted Drilling of SS304”, Elsevier, Procedia Materials Science 6 (2014), Pp. 1572 – 1579.
Gupta, K. K., Jain, T., Deshmukh, M. (2013) “Optimization of Process Parameters in High RPM Micro Drilling Machine” IJIET, Vol 2, Pp.128-130.
Hanif MI, Aamir M, Ahmed N, Maqsood S, Muhammad R, Akhtar R, et al. Optimization of facing process by indigenously developed force dynamometer. Int J Adv Manuf Technol 2019; 100(5):1893–905.
Hassanpour H, Sadeghi MH, Rezaei H, Rasti A (2016) Experimental Study of cutting force, micro hardness, surface roughness, burr size on micro-milling of TiAl4V in minimum quantity lubrication. Mater Manuf Process 31, Pp. 1654-1662, https://doi.org/10.1080/10426914.2015.1117629.
Heisel, U., Pfeifroth, T. (2012) “Influence of Point Angle on Drill Hole Quality and Machining Forces when Drilling CFRP”, Elsevier, Procedia CIRP 1 (2012), Pp. 471– 476.
Hinds, B. K., Treanor, G. M. (2011) “Analysis of stresses in micro-drills using the finite element method”, International Journal of Machine Tools and Manufacture 3(5), Pp. 13-18.
Hongyan, S., Song, F., Fu, L. (2011) “Experimental study on drilling force in printed circuit board micro drilling process” Circuit World, 37(1), 24-29.
Indumathi V. Reddy D, Krishnaiah, G. (2014) “Optimization of machining parameters using Desirability Function Analysis and ANOVA for thermo-mechanical form drilling,” International Journal of Industrial Engineering & Technology (IJIET), 4(1), Pp. 19-26, ISSN(P): 2277-4769; ISSN(E): 2278-9456.
Jayabal, S., Natarajan, U. (2010), “Influence of cutting parameters on thrust force and torque in drilling of E-glass/Polyester composites”, Indian Journal of Engineering & Materials Sciences, 17, Pp. 463-470.
Jiang, B., Lan, S., Ni, J., Zhang, Z. (2014) “Experimental investigation of spark generation in ECDM of non-conducting materials”, Journal of Materials Processing Technology, 214, Pp. 892–898.
Keerthi, N., Hussian, S. A. (2013) “Modelling and Analysis Of Machining Characteristics Of En-8 Steel In Drilling Process,” International Journal of Engineering Research & Technology (IJERT), 2(11), ISSN: 2278-0181.
KilickapE., Huseyinoglu, M., Yardimeden, A. (2011) “Optimization of drilling parameters on surface roughness in drilling of AISI 1045 using response surface methodology and genetic algorithm,” Int J Adv Manuf Technol 52, Pp. 79–88, DOI 10.1007/s00170-010-2710-7.
Kumar, J. P., Packiaraj, P. (2012) “Effect Of Drilling Parameters On Surface Roughness, Tool Wear, Material Removal Rate And Hole Diameter Error In Drilling Of Ohns”, International Journal of Advanced Engineering Research and Studies, 1(3), Pp. 150-154.
Liu, H. S., Lee, B. Y., Tarng., Y. S., (1998) “In-process prediction of corner wear in drilling operations”, Journal of Materials Processing Technology, Volume 101, 152-158.
Madhavan, S., Prabu, S. B. (2012). “Experimental investigation and Analysis of Thrust Force in Drilling of Carbon Fibre Reinforced Plastic Composites using Response Surface Methodology, International Journal of Modern Engineering Research (IJMER), 2(4), 2719-2723, ISSN: 2249-6645.
Murthy B.R.N., Lewlyn L., Rodrigues R., Devineni, A. (2012), “Process Parameters Optimization in GFRP Drilling through Integration of Taguchi and Response Surface Methodology,” Research Journal of Recent Sciences, ISSN 2277-2502, Vol. 1(6), Pp. 7-15.
Mustafa, K., Bagei, E., Kaynak,Y. (2009), Application of Taguchi methods in the optimization of cutting parameters for surface finish and hole diameter accuracy in dry drilling process., Int J Adv Manuf Technol, 40, 458-469.
Mustafa, A., Çaydaş U., Hasçalık, A. (2013), “Optimization of micro-EDM drilling of inconel 718 superalloy”, International Journal of Advance Manufacturing Technology, 66, Pp. 1015–1023.
Nalawade P.S. (2015) “Cutting Parameter Optimization for Surface Finish and Hole Accuracy in Drilling Of EN-31, IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE), e-ISSN: 2278-1684,p-ISSN: 2320-334X, Volume 12(1), Pp. 20-27.
Onwubolu, G. C., Kumar, S. (2006) “Response surface methodology-based approach to CNC drilling operations,” Journal of Materials Processing Technology, 171 (2006), Pp. 41–47.
Raj, M., Das, S. L., Palanikumarr, K. (2013) “Influence of Drill Geometry on Surface Roughness in Drilling of Al/SiC/Gr Hybrid Metal Matrix Composite”, Indian Journal of Science and Technology, 6 (7), ISSN: 0974-6846.
Rahman, A. A., Mamat, A. “Effect of Machining Parameters on Hole Quality of Micro Drilling for Brass”, International Journal of Machine Tools and Manufacture, 3(5) Pp. 221-230.
Ramesh Kumar, C., Jai Ganesh, V. & Malarvannan, R.R.R. Optimization of drilling parameters in hybrid (Al6061/SiC/B4C/talc) composites by grey relational analysis. J Braz. Soc. Mech. Sci. Eng. 41, 155 (2019). https://doi.org/10.1007/s40430-019-1661-7.
Razfar, M. R., Behroozfar, A., Ni, J. (2014), “Study of the effects of tool longitudinal oscillation on the machining speed of electrochemical discharge drilling of glass”, Precision Engineering, 38, Pp. 885–892.
Saran P (2014), “Experimental Analysis of the Effect of Process Parameters on Surface Finish in Radial Drilling Process”, International Journal of Engineering and Innovative Technology (IJEIT), 4(1), Pp.49-56, ISSN: 2277-3754.
Siddiquee, A. N. (2014) “Optimization of Deep Drilling Process Parameters of AISI 321 Steel using Taguchi Method, 3rd International Conference on Materials Processing and Characterization (ICMPC 2014), Elsevier, Procedia Materials Science 6, Pp. 1217 – 1225.
Singh, P., Bhambri, K. (2016), “Optimization of Process Parameters of AISI D3 Steel with Abrasive Assisted Drilling, International Research Journal of Engineering and Technology (IRJET), 3(4), ISSN: 2395 -0056.
Tosun, G., Muratoglu, M. (2004) “The drilling of Al/SiCp metal–matrix composites. Part II: work piece surface integrity”, Composites Science and Technology, 64, 1413–1418.
Tsao, C. C., Hocheng, H. (2008) “Evaluation of thrust force and surface roughness in drilling composite material using Taguchi analysis and neural network”, Elsevier, Journal of Materials Processing Technology 203, Pp. 342–348.
Tyagi, Y., Chaturvedi, V., Vimal, J. (2012) “Parametric Optimization of Drilling Machining Process using Taguchi Design and ANOVA Approach,” International Journal of Emerging Technology and Advanced Engineering, 2(7), ISSN 2250-2459.
Venkataramaiah, P., Kumar, G. V. (2012) “Design of Optimum ANN for Prediction of response parameters in drilling of En8 steel Under MQL environment,” International Journal of Emerging Technology and Advanced Engineering., 2(5), ISSN 2250-2459.
Vikas, S., Roy, A. K., Kumar, K. (2014) “Effect and optimization of machine process parameter son MRR for EN -19 and EN -41 using Taguchi”, Procedia materials science, Pp. 204-210.
Vimal, S., Latha, B., and Senthilkumar, V.S. (2009) “Modeling and analysis of Thrust force and Torque in drilling GFRP composites by multifaceted drill using fuzzy logic,” International Journal of Recent Trends in Engineering, 1(5), Pp. 66-70.
Uddin M, Basak A, Pramanik A, Singh S, KrolczykGM, Prakash C. Evaluating hole quality in drilling of Al 6061alloys. Materials 2018; 11(12):2443.
Yilmaz O., & Okka, M. A. (2010) “Effect of single and multi-channel electrodes application on EDM fast hole drilling performance”, International Journal of Advance Manufacturing Technology, Pp. 185–194.
Ziki, J. D. A., Wüthrich, R. (2013) “Forces exerted on the tool-electrode during constant-feed glass micro-drilling by spark assisted chemical engraving”, International Journal of Machine Tools and Manufacture, 73, Pp. 47–54.
